|
The Toyota Landcruiser Owners Club Landcruiser Club - Dedicated to Toyota Landcruiser, Amazon, Colorado and Prado Owners
|
View previous topic :: View next topic |
Author |
Message |
karl2000 ****
Joined: 25 Apr 2021 Posts: 318 Location: North West
|
Posted: Fri Nov 04, 2022 0:45 Post subject: |
|
|
Just found this procedure; if it doesn't work let me know. I think I've got a paper copy I scribbled over to clarify a few things. Here's what I've got anyway:
-----
Remote part programming
STEP1. Open Driver side door
STEP 2. Put the Original key in and out of ignition for 2 times
STEP 3. Close and open driver door for 2 times
STEP 4. Original Key in and out for once
STEP 5. Shut and open door for twice
STEP 6. Close door
STEP 7. Put Original Key in the ignition and Turn ignition on
STEP 8. Turn ignition off and remove key
STEP 9. Door locks will cycle
STEP 10. Do the following for all remotes:
Press lock and unlock together for 1s, then press the lock button
STEP 11. Locks will cycle put key in ignition turn to on then off
STEP 12. Remove key from ignition, close door and test remote
To Delete All Remotes from the Vehicle
At Step 7, turn the key on and off for 5 times then remove key, door locks will cycle for 5 times. Turn the key on then off. Open shut door. All remotes that were coded into the car, have now been removed.
2 Key part transponder chip programming manual (immobiliser)
STEP 1. Put Original master key in and out of ignition for 5 times. Finish with key in ignition (in, out, in, out, in, out, in, out, in)
STEP 2. Open and shut door for 6 times
STEP 3. Remove original key and insert the new key (Do not turn the key, just insert it into the ignition
STEP 4. Leave for 60s (or til light goes out)
STEP 5. After 60s security light stops flashing then you can start car.
STEP 6. Take key out
STEP 7. Open and shut door |
|
Back to top |
|
|
Google Sponsor
|
Posted: Fri Nov 04, 2022 0:45 Post subject: Google Ads keep this community free to join! |
|
|
|
|
Back to top |
|
|
karl2000 ****
Joined: 25 Apr 2021 Posts: 318 Location: North West
|
Posted: Fri Nov 04, 2022 1:19 Post subject: |
|
|
I wonder if the techstream version makes any difference? When I coded a key with it, I was using version 12.20, but I see you're on a much newer version.
My LC is also 2006, and I use the -0608 model when connecting |
|
Back to top |
|
|
Tractionman ******
Joined: 07 Apr 2007 Posts: 821 Location: Bournemouth, Dorset
|
Posted: Fri Nov 04, 2022 9:45 Post subject: |
|
|
Thanks Karl, that's what I was talking about. 👍
You didn't say anything about annoying the neighbours, opening and shutting doors 🤣 |
|
Back to top |
|
|
karl2000 ****
Joined: 25 Apr 2021 Posts: 318 Location: North West
|
Posted: Fri Nov 04, 2022 11:17 Post subject: |
|
|
Now I've programmed the keys I annoy them by dragging axle stands! |
|
Back to top |
|
|
Tractionman ******
Joined: 07 Apr 2007 Posts: 821 Location: Bournemouth, Dorset
|
Posted: Fri Nov 04, 2022 12:29 Post subject: |
|
|
👍🤣 I find once the BFH comes out and the swearing starts, it all goes quiet. 😠 |
|
Back to top |
|
|
el3388 *
Joined: 30 May 2014 Posts: 19 Location: UK
|
Posted: Sat Nov 05, 2022 13:48 Post subject: |
|
|
karl2000 wrote: |
Just found this procedure; if it doesn't work let me know. I think I've got a paper copy I scribbled over to clarify a few things. Here's what I've got anyway:
-----
Remote part programming
STEP1. Open Driver side door
STEP 2. Put the Original key in and out of ignition for 2 times
STEP 3. Close and open driver door for 2 times
STEP 4. Original Key in and out for once
STEP 5. Shut and open door for twice
STEP 6. Close door
STEP 7. Put Original Key in the ignition and Turn ignition on
STEP 8. Turn ignition off and remove key
STEP 9. Door locks will cycle
STEP 10. Do the following for all remotes:
Press lock and unlock together for 1s, then press the lock button
STEP 11. Locks will cycle put key in ignition turn to on then off
STEP 12. Remove key from ignition, close door and test remote
To Delete All Remotes from the Vehicle
At Step 7, turn the key on and off for 5 times then remove key, door locks will cycle for 5 times. Turn the key on then off. Open shut door. All remotes that were coded into the car, have now been removed.
2 Key part transponder chip programming manual (immobiliser)
STEP 1. Put Original master key in and out of ignition for 5 times. Finish with key in ignition (in, out, in, out, in, out, in, out, in)
STEP 2. Open and shut door for 6 times
STEP 3. Remove original key and insert the new key (Do not turn the key, just insert it into the ignition
STEP 4. Leave for 60s (or til light goes out)
STEP 5. After 60s security light stops flashing then you can start car.
STEP 6. Take key out
STEP 7. Open and shut door |
Karl, thanks a lot for the procedure. It works and I just programmed the key.
For the missing of the "Utility" function or the trimed-down version of Techstream, I still have no idea why it happens. |
|
Back to top |
|
|
Tractionman ******
Joined: 07 Apr 2007 Posts: 821 Location: Bournemouth, Dorset
|
Posted: Sat Nov 05, 2022 14:26 Post subject: |
|
|
HOORAY ! |
|
Back to top |
|
|
karl2000 ****
Joined: 25 Apr 2021 Posts: 318 Location: North West
|
Posted: Sat Nov 05, 2022 19:44 Post subject: |
|
|
Brilliant well done!
Try an older version of techstream, maybe they removed some functionality for the ancient vehicles out of the newer versions! |
|
Back to top |
|
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|